Công tắc hành trình SN02X12-732L-MC2432 (Euchner 123939)
Thông số kỹ thuật công tắc hành trình Euchner SN02X12-732L-MC2432 (Order no. 123939)
đại lý euchner | đại lý SN02X12-732L-MC2432 | đại lý 123939
nhà phân phối euchner | nhà phân phối SN02X12-732L-MC2432 | euchner 123939
| Rated operating distances Sn | 5 mm |
| Assured operating distances Sa | 0 … 4 mm (Dimension applies only to steel (ST37) and to EUCHNER trip dogs of series UX.. / GX..) |
| Center offset | |
| At s = 1 mm | mON= (-) 4.2 mm and mOFF= (-) 4.0 (For side approach) |
| At s = 3 mm | mON= (-) 2.5 mm and mOFF= (-) 2.0 (For side approach) |
| At s = 4 mm | mON= (-) 0.5 mm and mOFF= 0.0 (For side approach) |
| At s = 2 mm | mON= (-) 3.3 mm and mOFF= (-) 3.0 (For side approach) |
| Switching hysteresis | 0.2 … 1.0 mm (in the installed state) |
| Độ chính xác R | |
| according to EN 60947-5-2 | max. 5 % |
Operating and display elements
| LED display | |
| LED yellow | LED forward current IFmax. 2.5 mA |
Giá trị kết nối điện
| Kiểu đầu ra | PNP |
| Rated operating current Ie | 250 mA |
| Điện áp hoạt động | |
| DC | 20 … 24 … 33 V Power supply unit with electrical isolation as per EN 61558-2-6 or sensor pulsing UB(HIGH) |
| Operating current | max. 5 mA Mức tiêu thụ dòng điện without load |
| EMC yêu cầu bảo vệ | EN 60947-5-2 |
| Danh mục sử dụng | |
| DC-12 | 250 mA, 33 V (For DC-13, the output must be protected with a free-wheeling diode for inductive loads.) |
| Short circuit and overload protection, pulsed | yes |
| LOW level | |
| on sensor pulsing | 0 … 5 V DC |
| Off-state current Ir | max. 0.001 mA |
| Residual ripple | |
| From UBor UB(HIGH) | max. 10 % |
| Electrical switching frequency | max. 500 Hz |
| Cấp an toàn | |
| EN IEC 61140 | III |
| Voltage drop Ud | |
| DC | max. 2.5 V |
| Duty cycle Ton | |
| T (HIGH) : T (LOW) on sensor pulsing | 4 : 1 |
| Thời lượng xung kiểm tra | |
| T (LOW) on sensor pulsing | 0.1 … 20 ms |
| Bảo vệ phân cực ngược | yes |
| Kết nối type | |
| 1 x plug connector M12 (5-pin, straight plug connector: cable outlet not adjustable.) | |
| Kết nối terminals on the switching element | |
| Number NC contacts | 2 |
| Number of switching elements | 2 |
| Design | upright |
| Proximity switch spacing | 12 mm |
| Switching principle | Normally closed contact |
| Cấp bảo vệ | IP67 (only screwed tight with the related mating connector.) |
| Nhiệt độ môi trường | -25 … +70 °C |
| Material | |
| Thân | Die-c aluminum |
| Active face | PBT |
| C number | |
| C2432 | |
| Additional information | Thân without earth conductor! (All the electrical connections must either be isolated from the mains supply by a safety transformer according to EN IEC 61558-2-6 with limited output voltage in the event of a fault, or by other equivalent insulation measures.) |



